Laundering PPE

Laundering turnout gear

Turnout gear is a second skin. To protect you on the next call too, it must be properly laundered after a fire, without residues of laundry chemicals. Cleaning masks, helmets and harnesses is covered on the Cleaning PPE page.

The manufacturer's instructions always apply for the garment and the washing machine. The procedures on this page are based on professional PPE laundering practice and on technical data sheets of cleaning products. They are not results of independent studies.

Why laundering matters

After a fire, turnout gear holds soot with PAHs and keeps off-gassing combustion products. Poorly laundered PPE transfers contamination to the skin every time it is put on again. Ordinary washing removes coarse dirt but can leave a different problem in the material: residues of laundry and cleaning agents.

Aramid fibres

Alkaline residues from washing are bad for the fibres in the long run. Residues of soot and detergents in the fibres can reduce heat resistance.

Membrane

Grease and fine particles clog the micropores. The garment then wicks sweat less well and the firefighter overheats more.

Water-repellent finish

Residues of ionic surfactants make the outer fabric start absorbing water and liquid chemicals.

That is why it is important to choose products designed for firefighting PPE (low-foaming, with non-ionic surfactants, no fabric softener) and to rinse the garment thoroughly. Some crews finish with a neutralising rinse, for example with a weak organic acid, which brings the fabric's pH back to neutral. Chemical manufacturers' data

Laundering turnout gear

Before washing

Pre-cleaning

  • Remove coarse dirt already on scene
  • Spray heavily soiled gear, let it work, rinse
1st cycle

Wash outside out

  • Outer side out
  • Temperature according to soiling and manufacturer
2nd cycle

Wash inside out

  • Turn the gear inside out
  • Same programme again
After washing

Drying and inspection

  • Hang up, or dryer per the manufacturer's instructions
  • No direct heat or sun, then inspect

Pre-cleaning

Remove coarse dirt (mud, soot, debris) as soon as possible, ideally by wet decon right on scene. Spray the outer side of heavily soiled gear with a cleaning solution, let it work for a while and rinse thoroughly. Keep the coat closed and always rinse from top to bottom so that water doesn't needlessly get into the inner layers.

Why do it: if gear is laundered while covered in soot, the wash liquor is used up on the surface dirt and has no strength left for the grease and carcinogenic particles in the fibres. Coarse dirt can also damage the membrane through pressure and friction during washing.

How many items per machine

Machine capacityPer cycle
6–8 kgjacket only, or trousers only
9–12 kgjacket and trousers (1 set)
16 kg4 pieces (2 sets)

Don't overload the machine. The goal is for the solution to get into the fibres with as little friction as possible. Ideally wash one set per cycle.

Two cycles: outside out and inside out

  1. Stage 1, outer side out. Dose the product according to the degree of soiling and the instructions, and choose a programme according to the garment manufacturer.
  2. Stage 2, inside out. After the first cycle, turn the gear inside out, dose again and run the same programme. The inside is the side that touches the skin.
  3. Temperature: 40 °C for normal soiling, 60 °C for heavy soiling (grease, soot, oils), but only if the garment manufacturer allows it.
  4. Rinsing and spinning at the maximum speed the manufacturer allows. Low speeds leave more contaminated water in the gear.

Practical tip: for extremely soiled gear, 15–20 g of sodium carbonate (washing soda) can be added to the first stage to help neutralise acidic combustion products. The pH of the wash water should not exceed 9.5. If you can check pH, do so especially when combining with other products. Field experience

When the wash liquor is exhausted

A surfactant doesn't have a capacity measured in minutes. What matters is the ratio of surfactant to soiling. Soot, grease and combustion products bind the surfactant. Free surfactant in the bath decreases, and once it drops below the critical micelle concentration (CMC), micelles stop forming. Micelles are what surround greasy dirt and hold it in the water. Below the CMC the solution no longer picks up dirt, it just moves it around the fabric.

In practice you can tell by the foam: if there is foam at the start of the wash and it collapses during the cycle, the surfactant is used up. With heavily soiled gear this can happen very early. That is why gear is washed twice, each time with a fresh dose, and why removing coarse dirt before washing helps. Low-foaming PPE products foam little even at full strength, so with them foam is only a rough guide and dosing by the degree of soiling is more reliable. Expert judgement

How long to wash

Longer washing doesn't mean cleaner gear. Most of the dirt comes loose in about 10 to 15 minutes of main wash. If the cycle keeps running in the same bath, the solution is saturated with dirt and it starts going back into the fibres (redeposition). Longer washing also means more friction and longer exposure to heat and alkali, which wears the membrane, seams and reflective tape.

Two shorter cycles with a rinse between them give a better result than one long one: the first carries away most of the dirt along with the exhausted solution, the second works with a clean bath. Programme length and temperature are always set by the garment manufacturer's instructions, which take precedence. Expert judgement and field experience

Drying and inspection

Take the gear out and hang it up, or dry it in a dryer according to the garment manufacturer's instructions. For DEVA gear, for example, that means two drying cycles of 20 minutes each and then letting it finish drying in the air. Let the gear dry completely and then check it for damage. Further steps follow your crew's internal procedures and the garment manufacturer.

Reproofing

Gear can be reproofed after washing. How to do it and, above all, how to protect yourself from the chemicals in the product during application is described on the Reproofing page.

What to avoid

WrongRight
Fabric softenerCoats fibres with a flammable film and clogs the membrane. Forbidden for firefighting PPE.
No fabric softener, final rinse with clean water or a neutralising rinse
Home washing machine, washing at homeContamination spreads into the household and onto other laundry
Professional washer at the station or a specialist cleaner
Overloaded machineThe solution can't reach the fibres and friction increases
One set per cycle according to machine capacity
Low spin speed when rinsingMore contaminated water stays in the gear
Maximum speed allowed by the garment manufacturer
Drying on a radiator or in the sunHeat and UV radiation damage the material
Hang up, or dryer per the manufacturer's instructions

Safety when handling concentrates. Technical cleaning concentrates can cause serious eye damage and allergic skin reactions. Wear protective gloves and eye protection when diluting and dosing. If it gets in your eyes, rinse with water and call a poison control centre. Whoever launders and washes gear after a fire should also wear protective equipment because of the combustion products, see Station decon.