Laundering turnout gear
Turnout gear is a second skin. To protect you on the next call too, it must be properly laundered after a fire, without residues of laundry chemicals. Cleaning masks, helmets and harnesses is covered on the Cleaning PPE page.
The manufacturer's instructions always apply for the garment and the washing machine. The procedures on this page are based on professional PPE laundering practice and on technical data sheets of cleaning products. They are not results of independent studies.
Why laundering matters
After a fire, turnout gear holds soot with PAHs and keeps off-gassing combustion products. Poorly laundered PPE transfers contamination to the skin every time it is put on again. Ordinary washing removes coarse dirt but can leave a different problem in the material: residues of laundry and cleaning agents.
Aramid fibres
Alkaline residues from washing are bad for the fibres in the long run. Residues of soot and detergents in the fibres can reduce heat resistance.
Membrane
Grease and fine particles clog the micropores. The garment then wicks sweat less well and the firefighter overheats more.
Water-repellent finish
Residues of ionic surfactants make the outer fabric start absorbing water and liquid chemicals.
That is why it is important to choose products designed for firefighting PPE (low-foaming, with non-ionic surfactants, no fabric softener) and to rinse the garment thoroughly. Some crews finish with a neutralising rinse, for example with a weak organic acid, which brings the fabric's pH back to neutral. Chemical manufacturers' data
Laundering turnout gear
Pre-cleaning
- Remove coarse dirt already on scene
- Spray heavily soiled gear, let it work, rinse
Wash outside out
- Outer side out
- Temperature according to soiling and manufacturer
Wash inside out
- Turn the gear inside out
- Same programme again
Drying and inspection
- Hang up, or dryer per the manufacturer's instructions
- No direct heat or sun, then inspect
Pre-cleaning
Remove coarse dirt (mud, soot, debris) as soon as possible, ideally by wet decon right on scene. Spray the outer side of heavily soiled gear with a cleaning solution, let it work for a while and rinse thoroughly. Keep the coat closed and always rinse from top to bottom so that water doesn't needlessly get into the inner layers.
Why do it: if gear is laundered while covered in soot, the wash liquor is used up on the surface dirt and has no strength left for the grease and carcinogenic particles in the fibres. Coarse dirt can also damage the membrane through pressure and friction during washing.
How many items per machine
| Machine capacity | Per cycle |
|---|---|
| 6–8 kg | jacket only, or trousers only |
| 9–12 kg | jacket and trousers (1 set) |
| 16 kg | 4 pieces (2 sets) |
Don't overload the machine. The goal is for the solution to get into the fibres with as little friction as possible. Ideally wash one set per cycle.
Two cycles: outside out and inside out
- Stage 1, outer side out. Dose the product according to the degree of soiling and the instructions, and choose a programme according to the garment manufacturer.
- Stage 2, inside out. After the first cycle, turn the gear inside out, dose again and run the same programme. The inside is the side that touches the skin.
- Temperature: 40 °C for normal soiling, 60 °C for heavy soiling (grease, soot, oils), but only if the garment manufacturer allows it.
- Rinsing and spinning at the maximum speed the manufacturer allows. Low speeds leave more contaminated water in the gear.
Practical tip: for extremely soiled gear, 15–20 g of sodium carbonate (washing soda) can be added to the first stage to help neutralise acidic combustion products. The pH of the wash water should not exceed 9.5. If you can check pH, do so especially when combining with other products. Field experience
When the wash liquor is exhausted
A surfactant doesn't have a capacity measured in minutes. What matters is the ratio of surfactant to soiling. Soot, grease and combustion products bind the surfactant. Free surfactant in the bath decreases, and once it drops below the critical micelle concentration (CMC), micelles stop forming. Micelles are what surround greasy dirt and hold it in the water. Below the CMC the solution no longer picks up dirt, it just moves it around the fabric.
In practice you can tell by the foam: if there is foam at the start of the wash and it collapses during the cycle, the surfactant is used up. With heavily soiled gear this can happen very early. That is why gear is washed twice, each time with a fresh dose, and why removing coarse dirt before washing helps. Low-foaming PPE products foam little even at full strength, so with them foam is only a rough guide and dosing by the degree of soiling is more reliable. Expert judgement
How long to wash
Longer washing doesn't mean cleaner gear. Most of the dirt comes loose in about 10 to 15 minutes of main wash. If the cycle keeps running in the same bath, the solution is saturated with dirt and it starts going back into the fibres (redeposition). Longer washing also means more friction and longer exposure to heat and alkali, which wears the membrane, seams and reflective tape.
Two shorter cycles with a rinse between them give a better result than one long one: the first carries away most of the dirt along with the exhausted solution, the second works with a clean bath. Programme length and temperature are always set by the garment manufacturer's instructions, which take precedence. Expert judgement and field experience
Drying and inspection
Take the gear out and hang it up, or dry it in a dryer according to the garment manufacturer's instructions. For DEVA gear, for example, that means two drying cycles of 20 minutes each and then letting it finish drying in the air. Let the gear dry completely and then check it for damage. Further steps follow your crew's internal procedures and the garment manufacturer.
Reproofing
Gear can be reproofed after washing. How to do it and, above all, how to protect yourself from the chemicals in the product during application is described on the Reproofing page.
What to avoid
Safety when handling concentrates. Technical cleaning concentrates can cause serious eye damage and allergic skin reactions. Wear protective gloves and eye protection when diluting and dosing. If it gets in your eyes, rinse with water and call a poison control centre. Whoever launders and washes gear after a fire should also wear protective equipment because of the combustion products, see Station decon.